Showing results: 211 - 225 of 255 items found.
-
Thorlabs, Inc.
Thorlabs' expanding line of optical power and energy meters includes power meter consoles, a large selection of sensor heads, a wireless power meter with a built-in photodiode sensor, and a fiber optic power meter designed for use in the field. The consoles (PM100, PM400, and PM300 Series) when paired with our extensive line of power and energy sensors provide calibrated (NIST traceable) measurements across a broad range of powers, energies, and wavelengths. The console(s) and sensor(s) can be purchased individually or as bundles based on our most popular console and sensor pairings. The sensor calibration data is stored in the sensor head and is automatically read by the console, which allows the user to use multiple sensors with the same console. Compatible sensors are easily identified by the red c-series connector. All of our old A/B-Type sensors are available with the new connector; plus, we have continued to expand our power and energy sensor product lines.
-
MODEL LCA-9PC -
Transducer Techniques, Inc
The LCA-9PC Module provides low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-9PC comes with DB9 male and female connectors, which require soldering to user-furnished mating female or male wire connectors. On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film otentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
MODEL LCA-RTC -
Transducer Techniques, Inc
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Extech EC410 -
Extech Instruments Corporation
EC410 kit includes EC400 ExStik® Conductivity/TDS/ Salinity Temperature Meter, with sensor, protective cap, three calibration standards, (30mL bottle each), weighted base, 3 sample plastic cups, with caps, four 3V CR-2032 batteries, 48 in. (1.2 m) neck strap, and carrying case. Autoranging meter offers 3 ranges of measurements from tap water to wastewater and any aqueous solution. Automatic Temperature Compensation of 2% per °C. Data Hold, Auto Power Off and low battery indication. Internal memory stores up to 25 labeled readings for easy recall.
-
72-6635 -
Tenma
*Large LCD Display, easy to read*Characteristic of "A" frequency weighting network are designer to meet IEC 651 type 2*Fast time weighting characteristic mode*Build in adj. VR is available for easy calibration*Condenser microphone for high accuracy & long-term stability*Hold function to freeze the display value*Warning indicator for over and under range*LCD display for low power consumption & clear read-out even in bright ambient light condition*Durable, long-lasting components, including a strong, light weight ABS plastic case*Small and light weight design allow one hand operation*Low battery indicator*High quality with economical cost
-
AP-B Series -
Applied Image, Inc.
A unique concept in imaging calibration technology, The ACCUplace Bulls Eye / Recognition Grid allows the end user to calibrate magnification at multiple power levels, as well as test the system’s ability to recognize and locate distinctive shapes within shapes by focusing on the concentric circles.Each Bulls Eye / Recognition Grid target has individual patterns consisting of 5 concentric circles with 0.50mm line width and 0.50mm spacing between circles (10mm Pitch) with a 0.100mm center dot. In addition, each row and column is labeled with X & Y coordinates. The AP-B series is offered on four standard substrates; Chrome on Glass (CG) Opal (OP) Photopaper (RM) and Film (TM).
-
TMP117 (Qwiic) -
SparkFun Electronics
The SparkFun Qwiic TMP117 breakout is a high precision temperature sensor equipped with an I2C interface. It outputs temperature readings with high precision of ±0.1°C across the temperature range of -20°C to +50°Cs with no calibration and a maximum range from -55°C to 150°C. The SparkFun High Precision Temperature Sensor also has a very low power consumption rate which minimizes the impact of self-heating on measurement accuracy. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
DPNA-6G AXIe -
Holding Informtest
The AXI DPNA-6G module is the world's first network analyzer in the form factor of the AXIe-1 module, as well as the first Russian device that meets the AXIe-1 standard. In the mode of the network parameters meter, the AXI DPNA-6G module measures the vector values of the network parameters on two ports: transmission coefficients (S12, S21) and reflection (S11, S22). At the same time, all necessary types of calibrations are supported: one- and two-port short-circuit, XX, matched load, transmission normalization. The software supports the import of third party calibration standard parameters. In the measuring receiver mode, the module provides:*generation of a harmonic signal (frequency synthesizer);*spectrum analyzer and power level in a given band;*measuring the frequency of a known signal;*measurement of analog modulation parameters;*phase noise measurement.
-
MC133 -
Powertek LLC
The MC133 master unit model is a one phase electric power/energy calibrator. It can supply the device under test with single phase precise voltage and current with calibrated phase shift along with DC voltage and current capability. Output voltage can be set in five ranges up to 280V and output current in six ranges up to 30A. Simulated electric power can be set independently for each phase. Frequency can be set from 15Hz to 1 kHz with resolution 0.001Hz to 0.01Hz. The MC133 Calibrator is equipped with 5 1/2 digital DC meter with DC ranges 20mA or 10V for direct calibration of various types of power transducers and wattmeters.
-
S94702A -
Keysight Technologies
The Keysight automated measurement expert (AMX) is a smart software solution for automated multiport S-parameter measurements with the PXIe vector network analyzers M937xA/M9485A or the benchtop E5080A ENA network analyzer. The S94702A AMX VNA plugin adds S-parameter measurement capabilities to the Keysight test automation platform (TAP). The combination of the TAP and the VNA plugin forms the AMX backend software, which makes the VNA setups and executes the test sequences in the PXIe controller according to the optimized test sequence files generated by the AMX test plan builder. Other instrument plugins allow you to control the DUT mode, expand the number of test ports with the PXI switches or multiport test set, and use external instruments such as a DC power supply and a digital multimeter. The AMX backend software also provides step-by-step calibration wizard for full multiport calibration using the 4-port ECal module.
-
AmpConnect™ ISC -
Listen Inc
AmpConnect ISC is an all-in-one audio interface that simplifies your test setup and operation. It is a single, rugged, rack-mountable piece of hardware containing a high-accuracy audio interface, impedance box, amplifier, headphone amplifier, 2 microphone power supplies and digital I/O. It replaces multiple hardware devices, connecting to your computer via a single USB cable, and it is fully controlled by SoundCheck. This simplifies setup and calibration, eliminates cabling and reduces connectivity errors, as well as reducing overall system cost.
-
TM263N -
T&M Tools Limited Co
◇ Added Network Cable Test ◇ Accurately test whether a single network cable transmits signals normally ◇ Self Calibration ◇ Set the Auto Off ◇ Wavelength Memory function after turn off the tester ◇ High Accuracy, high ,High sensitivity, high linearity ◇ Stable VFL Output ◇ USB Charge port ◇ FC,SC Connector ◇ 18650Li-ion Battery ◇ Lower power consumption design, long standby time ◇ Rubber Out shell, increased the protective properties for field work
-
N5183B -
Keysight Technologies
Get a fast, compact (2U) alternative to the PSG in the lab, depot or fieldAddress demanding tests of radar modules & systems with near-PSG levels of spectral purityCompensate for system loss & drive high-power amplifiers: +19 dBm output power, -55 dBc harmonics & -68 dBc spurious @ 20 GHzReduce calibration time with switching speed 600 sSimulate narrowband chirps & radar antenna scans with up to five internal function generators that can be used with AM, FM, OM pulse modulation
-
Vetek Weighing AB
BTR is a desktop torque for torque meas urements consisting of a digital indicator model DTR and a strain gauge torque extremely rugged and compact which has a precision better than 0.20%. Ideal for the calibration and the control of torque keys and to rque screwdrivers. Microprocessor indicator is fed by 4 internal batteries with an autonomy of 200 hours, with the AUTO POWER OFF function which activates if any change in the measurement is detected in an interv al of 30 minutes. The new generation electronic section consists of a particularly long-term stable analogue circuit and of a 16 bits A/D converter which ensures 65.000 internal divisions with an acquisition sp eed of 200 conversions per second. On the display there is an analogue bar for torque, that is still active, even in the programming menu.
-
MD-250-M -
Mustang Dynamometer
Mustang has developed a low-cost, simple to use, easy-to-install heavy duty chassis dynamometer that can be used to simulate real-world driving conditions in a safe, controlled environment and can also be used for “static” diesel smog testing for regulatory purposes. This model is used in Diesel Smog Programs in Nevada and Colorado when combined with an approved opacity meter. The MD-250-M is a compact dynamometer with industry proven design features including 10.7-inch rollers, heavy duty spherical pillow-block ball bearings, welded structural steel frame, 7.5 hp calibration motor, and an industry standard air-cooled, Eddy Current Power Absorption Unit (PAU) for road-load simulation. The MD-250-M is available in both right and left hand configurations to accommodate different facility designs.
